ARRMA Compatible 30T M1.5 Spur Gear MAKX030TS for 1/5 Kraton Outcast by GPM  [MAKX030TS]

Price:
£12.79
Brand:
GPM
Model:
MAKX030TS
GTIN:
4894538416794
Condition:
Brand New
Write a review

MAKX030TS: 30T M1.5 spur gear summary

The MAKX030TS is an aftermarket spur gear made as a direct replacement for ARRMA 1/5 Kraton and Outcast vehicles. It is a 30-tooth component with M1.5 module, produced in 20CrMnTi steel to provide higher wear resistance and improved bending strength over softer factory alloys.

Intended for demanding 8S BLX brushless systems, the gear supports applications where durability and steady tooth engagement are vital. Proper fitment involves confirming M1.5 module compatibility and adjusting pinion/spur mesh and shims; it substitutes the factory reference numbers listed below.

Packing includes

  • Spur Gear 30T Mod 1.5 - 1pcs

Original Name / Part No:

ARA310920?ARA311051

Compatible Models

  • ARRMA 1/5 Kraton 4X4 8S BLX Brushless Speed Monster Truck RTR-ARA110002 (Original Spur Gear 47T/M1.0)
  • ARRMA 1/5 Outcast 4WD 8S BLX Stunt Truck RTR-ARA5810 (Original Spur Gear 47T/M1.0)
  • ARRMA 1/5 Kraton 8S EXB 4X4 Roller Brushless Speed Truck-ARA5208 (Original Spur Gear 39T/M1.0 & 47T/M1.0)
  • ARRMA 1/5 Kraton 4X4 8S BLX EXB Brushless Monster Truck RTR-ARA5808V2 (Original Spur Gear 47T/M1.0)
  • ARRMA 1/5 Outcast 8S EXB 4X4 Roller Brushless Stunt Truck-ARA5210 (Original Spur Gear 39T/M1.0 & 47T/M1.0)
  • ARRMA 1/5 Outcast 4X4 8S BLX EXB Brushless Stunt Truck RTR-ARA5810V2 (Original Spur Gear 47T/M1.0)

This 20CrMnTi 30T M1.5 spur is suited to applications needing a stronger aftermarket gear; always verify module and mesh during installation and re-check after the first run.

What is the best way to check gear mesh with this part?

Start with the recommended pinion for M1.5, set a light running clearance by feel or with a thin gauge, then tighten and run the car slowly to confirm smooth engagement before full-power use.

How does M1.5 affect existing gearsets?

M1.5 requires a matching pinion and mating gears; if your original set uses a different module, you will need to swap the pinion or the spur accordingly to maintain correct mesh.

Will this replace the listed ARRMA part numbers directly?

It is marketed as a replacement for the factory references noted above. Confirm the part numbers against your vehicle's manual or parts list prior to purchase.

Any run-in procedure recommended?

After installation, run the vehicle at low speed for a short period to allow components to settle, then re-check mesh, fasteners and bearing play before normal use.

Is this suitable for upgraded motors and ESCs?

The gear is intended to withstand higher-output systems such as 8S BLX, but ensure the rest of the drivetrain and cooling are appropriate for upgraded electronics.

Do I need specialised tools to fit this gear?

Basic RC tools are sufficient for fitting: hex drivers, feeler gauges or shims for mesh, and a torque-appropriate driver for mounting screws; no special presses are normally required.

Copyright © 2008-2026 rcjaz.co.uk All rights reserved