AXIAL SCX10 II Precision Centre Shaft SSCX27037 Steel/Aluminium by GPM  [SSCX27037]

AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037
Price:
£25.07
Brand:
GPM
Model:
SSCX27037
GTIN:
4894538259070
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
category
Write a review
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"

Precision centre shaft for SCX10 II crawlers

The SSCX27037 centre shaft set is a purpose-built RC replacement for AXIAL Racing SCX10 II platforms. It uses steel at high-load joints and aluminium on rotating parts to keep strength where needed while trimming inertia for better low-speed control.

Lower rotating mass reduces drivetrain stress during slow crawling and can improve throttle modulation under heavy articulation. The components are matched to SCX10 II suspension behaviour and provide a direct swap for experienced hobbyists and builders.

The set includes small hardware for mounting: M4*2.5*11 screw shaft - 4pcs, 4*2.5 O-ring - 4pcs.

Compatible Models

  • Axial SCX-10 II AX

Fit this shaft set to achieve a lighter central driveline assembly for scale crawling setups on SCX10 II, and carry out regular lubrication and joint checks after installation.

Is SSCX27037 compatible with my SCX10 II axle package?

Confirm your existing shaft dimensions against the listed S:118mm-128mm and L:130mm-140mm ranges; compatibility is determined by those length ranges rather than model year alone.

Will aluminium parts corrode against steel?

When steel and aluminium are used together, keep contact areas clean and lightly lubricated; regular inspection helps prevent galvanic wear in outdoor or damp conditions.

Are spare O-rings available separately?

The kit includes four 4*2.5 O-rings; source replacements from common RC parts suppliers if you plan frequent disassembly or run in harsh environments.

What should I check after the first runs?

After initial installation, retorque screws, inspect for any unusual play, and reapply lubricant if necessary following a brief break-in session.

Does this kit affect gearing or ground clearance?

This shaft set is focused on reducing rotating mass and does not change gear ratios or ride height; confirm fitment if you run custom axle or gearbox modifications.

Copyright © 2008-2026 rcjaz.co.uk All rights reserved