Slash 4X4 Performance Front C Hub 7075 Alloy SLA019N by GPM  [SLA019N]

TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N
Price:
£21.48
Brand:
GPM
Model:
SLA019N
GTIN:
4894538387933
Condition:
Brand New
Write a review
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"

Performance front C hub for Slash 4X4

The SLA019N front C hub is a precision replacement for TRAXXAS Slash 4X4 and a selection of 1/10 4WD platforms. Manufactured from 7075 alloy, it relocates the knuckle mount to a bearing interface rather than a plain shaft hole, helping to reduce steering lash and provide more consistent feedback. Multiple tie rod positions allow you to dial roll centre and toe for your preferred handling balance.

Fitting uses the vehicle's original front C-hub mounting points and the supplied fasteners for a direct installation. The bearing-mounted knuckle requires accurate bearing seating and recommended thread-lock on metal fasteners. This product is intended for hobby RC applications and aligns with the compatible models shown below.

Packing includes

  • C-Hub - 1pcs
  • King Pin - 1pcs
  • Grade 12.9 black Round Head Screws 3x14 - 1pcs
  • Grade 12.9 black Round Head Screws 3x16 - 1pcs

Original Name / Part No:

6832

Compatible Models

  • TRAXXAS-SLASH 4X4 LOW-CG-68086-21
  • TRAXXAS 1/10 RUSTLER 4X4 VXL-67076-4
  • TRAXXAS 1/10 4WD HOSS 4X4 VXL 3S-90076-4
  • TRAXXAS 1/10 Ford Fiesta ST Rally-74064-4
  • TRAXXAS 1/10 Ford Fiesta ST Rally-74054-4
  • TRAXXAS 1/10 Rustler 4X4-67064-1
  • TRAXXAS 1/10 Rustler 4X4-67064-61
  • TRAXXAS 1/10 Slash 4X4 VXL-68086-4
  • TRAXXAS 1/10 Slash 4X4-68054-1
  • TRAXXAS 1/10 Slash 4X4-68054-61
  • TRAXXAS 1/10 Slash 4X4 VXL-68286-4
  • TRAXXAS 1/10 Stampede 4X4 VXL-67086-4
  • TRAXXAS 1/10 Rustler 4X4 Ultimate-67097-4
  • TRAXXAS 1/10 Slash 4X4 Ultimate-67097-4
  • TRAXXAS 1/10 Slash 4X4 Ultimate-68277-4

Install the SLA019N to tighten front-end steering and remove knuckle slop; use the multiple tie rod holes to refine handling for circuit or loose-surface running and confirm bearings and screw torque after fitting.

Is this a direct replacement for stock plastic hubs?

Yes, where the vehicle code matches the Compatible Models list, SLA019N installs using the stock front c-hub mounting points and the included hardware for a direct swap.

Will stiffer alloy affect tyre wear?

Stiffer steering components can change contact and feedback, so check alignment and tyre condition after fitting and adjust geometry if you notice uneven wear.

Can I tune steering with the supplied hub alone?

The multiple upper tie rod positions provide meaningful tuning of roll centre and toe, but combine hub changes with shock settings and toe adjustments for best results.

What checks after first fitment?

After the first run, recheck bearing seating, retorque screws and verify steering play is within your expected tolerance. Make small adjustments and retest.

Copyright © 2008-2026 rcjaz.co.uk All rights reserved