TRAXXAS-Compatible 56T Steel Spur Gear SSLA2W056T by GPM  [SSLA2W056T]

TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T
Price:
£14.27
Brand:
GPM
Model:
SSLA2W056T
GTIN:
4894538365818
Condition:
Brand New
Write a review
alt="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T" title="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T"
alt="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T" title="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T"
alt="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T" title="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T"
alt="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T" title="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T"

56T hardened steel spur for TRAXXAS 1/10 2WD

This 1/10-scale spur gear is a 56-tooth, 0.8 module unit intended for driveline use in compatible TRAXXAS 2WD models. Manufactured from hardened black carbon steel via CNC machining, it replaces the standard nylon spur where improved wear resistance and consistent tooth contact are required. It fits into the rear gearbox and transmits torque from the pinion to the drivetrain.

The package includes the main 56T spur gear plus three stainless steel washers for axial spacing; the gear follows a rugged 0.8 module profile and is produced to fit the listed TRAXXAS 1/10 2WD models. After fitting, verify gear mesh, remove any sharp edges, and ensure bearings and lubrication are correct for reliable service.

Packing includes

  • Spur Gear 56T - 1pcs
  • Stainless Steel Washer 3*7*0.2 - 3pcs

Original Name / Part No:

4690,4683,4686

Compatible Models

  • TRAXXAS-1/10 ELECTRIC 2WD F-150 SVT RAPTOR-58064-2
  • TRAXXAS-1/10 2WD BANDIT XL-5 BUGGY-24054-1
  • TRAXXAS-1/10 2WD BANDIT XL-5 BUGGY-24054-61
  • TRAXXAS-1/10 2WD BANDIT XL-5 BUGGY-24054-4
  • TRAXXAS-1/10 2WD BANDIT VXL BRUSHLESS BUGGY-24076-74
  • TRAXXAS-1/10 2WD BANDIT VXL BRUSHLESS BUGGY-24076-4
  • TRAXXAS-1/10 2WD SLASH SHORT COURSE TRUCK-58014-4
  • TRAXXAS-1/10 2WD SLASH SHORT COURSE TRUCK-58024
  • TRAXXAS-1/10 2WD SLASH SHORT COURSE TRUCK-58034-1
  • TRAXXAS-1/10 2WD SLASH SHORT COURSE TRUCK-58034-61
  • TRAXXAS-1/10 2WD SLASH VXL SHORT COURSE TRUCK-58076-74
  • TRAXXAS-1/10 2WD SLASH VXL SHORT COURSE TRUCK-58076-4

Suitable as a direct steel replacement for compatible TRAXXAS 1/10 2WD kits; always confirm pinion match and clearance before extended runs.

Can I use this on a brushed or brushless setup?

Yes, it fits both brushed and brushless setups listed in the compatibility section. Ensure your power system and gearing are matched to avoid overstressing the drivetrain.

What should I inspect after the first runs?

Check the mesh for wear patterns, confirm washers are in place, inspect bearings, and listen for unusual noise that may indicate pinion or tooth mismatch.

Is the 0.8 module a common pitch for these TRAXXAS models?

Yes, the listed TRAXXAS 1/10 2WD vehicles use a 0.8 module spur gear; fitting this 56T should preserve the original pitch and ratio when used as specified.

Will steel spur increase pinion wear?

Potentially, if the pinion is soft or worn. Check the pinion condition and replace it if you observe excessive wear to maintain longevity of the drivetrain.

Copyright © 2008-2026 rcjaz.co.uk All rights reserved